OAT now ships to various international countries
Products
Filters
10-pin ribbon cable for MKS/LCD
A pre-crimped 10 pin ribbon cable to connect a LCD shield to the MKS's EXP1 port. Comes with a 10-pin Dupont cable attached so you just have to co...
View full details60 M3x4.6x6 mm Heatinserts
60 M3x4.6x6mm Inserts for OAT. At this point this product can only be purchased in combination with other items!
LCD Shield
A standard LCD shield suitable for Arduino Mega or MKS (with the ribbon cable)
OAG v3.1 Upgrade Kit
Update your OAG v3.0 to the latest v3.1 version with this upgrade kit.
OpenAstroExplorer - Bearing Kit
All bearings for the OpenAstroExplorer 2x 6012 ZZ 6x 625 ZZ ABEC5 4x F695 ZZ 2x 6907 1x F6006 1x 51111 1x LM5UU
OpenAstroExplorer - Clamp Kit
All Arcaswiss clamps and plates used for the OpenAstroExplorer. 1x 120mm Clamp & Plate set 1x 90mm Clamp 1x 200mm Plate
OpenAstroExplorer - Electronics
Electronic components for the OpenAstroExplorer. If you need all electronics, you have to purchase all 3 options! PCB: PCB only Electronics: ...
View full detailsOpenAstroExplorer - Extrusions Kit
All Extrusion are drilled and tapped, ready to use. 1x 2020 300mm 1x 2020 200mm 1x 2020 50mm 1x 4040 75mm
OpenAstroExplorer - Hardware only Kit
OpenAstroExplorer - Motion Kit
All Motion components for the OpenAstroExplorer 4x GT2 16T Pulley 2x GT2 48T Pulley 3x GT2 looped belts 1x Worm gear set 1x MGN9C linear rail 2x S...
View full detailsOpenAstroExplorer - Pre-Built Mount
I am unclear whether or not I will actually offer a pre-built OpenAstroExplorer. Leave your Email in the "Notify me when available" form if you wou...
View full detailsOpenAstroExplorer - Screws and small Parts
OpenAstroExplorer DIY Kit
OpenAstroGuider v3.1
OpenAstroGuider: Your Affordable Autoguider for Stunning Astrophotography Unlock the cosmos without breaking the bank with the OpenAstroGuider. Des...
View full detailsOpenAstroGuider v3.1 - Hardware only
Non-printed Hardware needed to build an OpenAstroGuider v3.1 Version 3.1 requires the use of the custom PCB and a USB C cable. You need the PCB reg...
View full detailsOpenAstroGuider v3.1 - Printed Parts
Struggle to get the tolerances right for the OpenAstroGuider? These parts here have as perfect tolerances as its probably possible. The focus thre...
View full detailsOpenAstroMount - Screws & Nuts
All screws and nuts for assembling an OpenAstroMount. Screws are either 8.8/10.9 zink plated or A2 stainless. 4x M3x6 30x M3x10 100x M3x12 200x ...
View full detailsOpenAstroTracker - GoTo Mount - DIY Kit
Build it yourself! The DIY Kit includes everything you need to build your own OpenAstroTracker and get started in Astrophotography! You will need y...
View full detailsOpenAstroTracker - Hardware only
Complete Kit of all the non-printed parts to build an OpenAstroTracker. If you need Threaded Inserts for the _TI version of the printed parts, add ...
View full detailsOpenAstroTracker - Printed parts only
All mechanical printed parts to build an OpenAstroTracker. The RA Ring is NOT included! The two moving DEC parts have their 6001 bearings press-fit...
View full detailsOpenAstroTracker - Single piece RA Ring
This RA Ring for the OpenAstroTracker is printed in a single piece and has the middle part reinforced. This reduces the error caused by joining the...
View full details